Glossary
Terms used in this course and in the rest of the guide, in alphabetical order.
| Term | Meaning |
|---|---|
| AC analysis | Small-signal simulation over frequency: gain and phase of every node for a 1 V sine at the input. Gives Bode plots. |
| Active (diffusion, OD) | The layout layer where silicon is left exposed for transistors and taps. A transistor is poly crossing active. |
| Bias | The DC voltages and currents that set where transistors operate. |
| Bode plot | Gain (dB) and phase (°) against frequency on a log axis. |
| Body (bulk, B) | The fourth MOSFET terminal: the silicon under the channel. Substrate (ground) for NMOS, n-well (VDD) for PMOS. |
| BSIM4 | The industry-standard compact MOSFET model used by most foundry PDKs. |
| Channel | The thin inverted layer under the gate that conducts when the transistor is on. |
| Channel-length modulation (λ) | The small rise of drain current with VDS in saturation; sets ro. |
| CMOS | Complementary MOS: logic built from NMOS pull-down and PMOS pull-up networks. |
| Common centroid | Interleaving matched devices (ABBA) so they share the same centre, cancelling process gradients. |
| Contact | A metal-filled hole connecting metal1 to active or poly. |
| Corner | A model set for a process extreme: tt (typical), ff (fast), ss (slow), fs, sf. |
| dB (decibel) | 20·log₁₀ of a voltage ratio. ×10 = 20 dB, ×0.707 = −3 dB. |
| dbu | Database unit of layout coordinates; 1 dbu = 1 nm in the generic technology. |
| DC sweep | A series of operating points while one source is stepped. |
| Design rules | The fab’s geometric limits: width, spacing, enclosure, extension, area, density. |
| Die | One chip, cut from the wafer. |
| Differential pair | Two matched transistors with a shared tail current; amplifies the difference of two inputs. |
| Doping | Adding impurities to silicon: n-type (extra electrons) or p-type (holes). |
| DRC | Design Rule Check: verifies a layout against the design rules. |
| Drain, source | The two ends of the channel. Carriers flow from source to drain. |
| Dummy | An unused device placed at the end of a matched row so every active device has the same surroundings. |
| Fab (foundry) | The factory that manufactures the chips. |
| Finger | One of several parallel narrow gates that together form a wide transistor. |
| Flyline | A straight dashed line in a layout showing a connection still to be routed. |
| gm (transconductance) | Change of drain current per volt of gate voltage: 2·ID/Vov. |
| gds, ro | Output conductance and resistance of a transistor in saturation; gds ≈ λ·ID. |
| GDSII | The binary file format of layouts sent to the fab (OASIS is its newer, smaller successor). |
| Gate | The control terminal of a MOSFET, insulated from the channel by the gate oxide. Also: a logic gate (NAND, NOR …). |
| Gate oxide | The thin insulator (a few nm of SiO₂) between gate and channel. |
| Ground | The 0 V reference net, 0 in SPICE. |
| Guard ring | A ring of taps around a device or block that collects stray carriers. |
| Inverter | The NOT gate: one PMOS and one NMOS. |
| KCL / KVL | Kirchhoff’s current and voltage laws, the equations a simulator solves. |
| Latch-up | A parasitic thyristor in CMOS that can short the supply; prevented by taps and guard rings. |
| Layout | The physical drawing of a circuit: polygons on mask layers. |
| LVS | Layout Versus Schematic: verifies the layout is the same circuit as the schematic. |
| Mask | A stencil for one lithography step; one layout layer. |
| Matching | Making devices that must be equal as identical as possible, by size and layout. |
| Metal1, metal2 … | The wiring layers, stacked above the transistors, joined by vias. |
| Monte Carlo | Many simulations with random process variation, to see the spread of a result. |
| MOSFET | Metal-oxide-semiconductor field-effect transistor. |
| Net (node) | A set of connected wires and pins, all at one voltage. |
| Netlist | The text description of a circuit: one line per device, listing its nets and values. |
| NMOS / PMOS | MOSFET with an n-type (electron) or p-type (hole) channel. |
| Noise margin | How much noise a logic input tolerates before it is read wrongly. |
| N-well | An n-type region in the p-substrate that holds PMOS transistors. |
| Operating point (OP) | The DC solution of a circuit with all inputs held still. |
| OTA | Operational transconductance amplifier: differential input, high-impedance output. |
| Overdrive (Vov) | VGS − Vth. |
| Parasitics | Unwanted resistance and capacitance of real wires and junctions. |
| PCell | Parameterised cell: a layout generator that draws a device from parameters such as W and L. |
| PDK | Process Design Kit: layers, rules, device models and PCells of a fab process. |
| PEX | Parasitic extraction: computing parasitics from a layout. |
| Pelgrom’s law | Random mismatch falls as 1/√(W·L). |
| Poly (polysilicon) | The gate layer. |
| Post-layout simulation | Simulation with extracted parasitics included. |
| Propagation delay (tp) | Time from the input crossing 50 % to the output crossing 50 %. |
| Saturation | The MOSFET region where VDS ≥ Vov and the current depends mainly on VGS. |
| Schematic | The circuit drawn as symbols and wires. |
| Square law | ID = ½·k’·(W/L)·Vov² in saturation. |
| SPICE | The standard circuit simulator family and its netlist format. |
| Substrate | The wafer silicon under all devices; p-type in the generic process. |
| Supply (VDD) | The positive power net, 1.8 V in the generic technology. |
| Tap | A contact to the substrate or well that ties the transistor bodies to their supply. |
| Tape-out | Sending the final layout to the fab. |
| Testbench | The sources, loads and analyses around a circuit that exercise it in simulation. |
| Threshold voltage (Vth) | The gate voltage at which the channel forms; 0.45 V for the generic NMOS. |
| Transient analysis | Simulation over time. |
| Triode (linear) | The MOSFET region where VDS < Vov; the channel acts as a resistor. |
| Unity-gain frequency | The frequency where the gain falls to 1 (0 dB). |
| Via | A metal-filled hole connecting two metal layers. |
| VTC | Voltage transfer curve: a gate’s output against its input. |
| W, L | Channel width and length, the sizes a designer chooses. |
| Wafer | The silicon disc, up to 300 mm across, on which chips are made. |
Further reading
- Behzad Razavi, Design of Analog CMOS Integrated Circuits — the standard analog text, very readable.
- Neil Weste and David Harris, CMOS VLSI Design: A Circuits and Systems Perspective — digital CMOS, layout and design rules.
- Jan Rabaey, Anantha Chandrakasan and Borivoje Nikolić, Digital Integrated Circuits — inverters, gates, delay and power in depth.
- Tony Chan Carusone, David Johns and Ken Martin, Analog Integrated Circuit Design.
- R. Jacob Baker, CMOS: Circuit Design, Layout, and Simulation — with many practical layout examples.
- Open PDKs to practise on real processes: SKY130 (SkyWater 130 nm) and IHP SG13G2, both supported by IC Studio (see Technology).